[bigmac]

Nope never an option on omega’s all ready asked on the omega forums when trying to source valve sensors :thumbdown

Best bet would be a kit off ebay

I have a spare ncdr2011 fascia board if anyone ever needs one think they were common in omega’s and vectra’s

[bigmac]

Its not the unit that controls the TPMS though its a control box that lives in the boot thats connected to the main wiring harness of the car,this in turn is linked to 4 receivers that are under each wheel arch,so as the vectra b didnt have this as an option you would have to make a complete new harness for the front Receivers and a new rear axle harness along with a harness that connects into the main engine bay ecu to back of car to control box.

A lot of mucking about just for check control,i’m lucky enough to have the front TPMS plugs and the control box plug,i have bought the wheel sensor’s and receivers along with control box and a new rear axle harness

If you need pointers to making a harness just pm me and i can help you but it will cost you more than it would for a vectra c as you will need to wire the whole lot in

[bigmac]

Dont think it can as i’m sure the vectra b dont use canbus :( you can fit an after market kit that has the sensors and screen off ebay

Thanks guys zodat het lijkt haar alleen maar een controle controle, zodat u huicheltaal toegankelijk vanuit het CID-menu? heeft iemand nog geen foto’s van de TPMS instellingen op CID?

Kan iemand te vinden uit de Opel-dealers welke modules moeten instelling dan indien mogelijk

Nogmaals bedankt voor al je hulp

[bigmac]

Hello mate you under same name on vectra c ? that would be good if you could as most technitions here haven’t got a clue tbh

Will wait and see if anyone else on here can help its just ive had a few members say they cant find anything in the NCDC menu’s regarding tyre pressure’s which i feel is a bit strange as you should be able to check them like the CD70 does
But some have said it just pop’s up when pressure is low like check control warning’s

[bigmac]

Originally posted by speaker
Welcome here Mac ( Big?)

I don’t know nothing about the NCDC2015, but I have the CD70 in my vec. On the CD70 is an option in the BC-setting , but it’s only to set it On/Off. If you don’t have sensors on your wheels , then the CD70 won’t bother you with any annoying messages on your screen.
So I think if you put some sensors on your wheels/rims , the message will pop-up automatically. Or you need a tech-2 ,like above message ! :thumbup

Btw: Where you’re from??

And maybe a little bit easier for you , will be http://www.vectra-c.com !

@ SWReijnders: C-section is a term they use in the Operation-room at the hospital ! :angel

Sorry guys i only speak English :( were one of the ignorant countries in the world as we expect everyone else to speak it :wub

I should of started off like this

Hi my name is Don i’m 38 years old and live in the UK i’m a Moderator on Vectra-c.com and have been modding my vectra c 2.0 Dti for well over 2 yrs.
I’m currently retrofitting the TPMS system to my vectra c but wanted to know if anyone on these forums has the same sort of setup as me eg: NCDC2013/15 + CID so i could see what if any settings there are on the screen when its all fitted.

I know the CD70 has its own menu where you can see the pressure’s of each wheel and just wanted to know if it will be the same on the NCDC screen.

The reason ive asked on these forums is because iirc TPMS was very much standard fit to most of the foreign vectra’s

Anyway thanks for all your welcome’s and hopefully some one will be able to point me in the right direction

PS….Dont suppose anyone knows what settings need to be activated in TECH2 do they ?

[Auteur]

Berichten